AGGREGATE CRUSHİNG VALUE APPARATUS

Aggregate Crushing Value Apparatus. Aggregate crushing value provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Consists of ∅ 150 mm steel cylinder, plunger, base plate, tamping rod ∅ 16 x 600 mm and measure ∅ 115 x 180 mm deep. Used for aggregate passing 12.7 mm …

Aggregate Crushing Value Apparatus

The oven dried and accurately weighed aggregates are subjected to crushing test on compression testing machine and weight of the resultant fines passing the specified IS sieve to the total weight of the sample expressed a s a percentage is defined as Aggregate Crushing Value. The apparatus is available in three size 75mm dia for 1/8" to ¼ ...

Aggregate Crushing Value Test

Apparatus. A 15.2 cm diameter steel cylinder with a plunger and a base plate. ... The aggregate crushing value for good quality aggregate used in base course shall not exceed 45 percent, and the value for surface course shall be less than 30 percent. The aggregate crushing value of coarse aggregates to be utilized for cement concrete …

Aggregate Crushing Value Test

Aggregate Crushing Value Test The objective of this test is to: Determine the aggregate crushing value of coarse aggregate; Assess suitability …

Aggregate Crushing Value Apparatus

Aggregate Crushing Value Apparatus. Aggregate Crushing Value Apparatus. As per IS:2386 (P-IV), IS:9376 for measuring resistance of aggregate to crushing, it consists of : 1 No. Cylindrical Container 150mm I.D. x 130mm to 140mm ht. with base plate & plunger. 1 No. Tamping Rod 16mm dia. x 600mm long. 1 No. Metal Measure 115mm dia. x 180mm ht.

Aggregate Crushing Value Apparatus

Standards:IS 2386 (PART-IV) & BS 812:111 Specification: The Aggregate Crushing Value (ACV) test set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder …

Get Aggregate Crushing Value

Specification:-. Aggregate Crushing Value Apparatus comprising 75 mm nominal diameter steel cylinder, plunger and base plate with metal measure and tamping rod (8 mm diameter 300 mm long with rounded end.) Be the first to review "Aggregate Crushing Value Apparatus". Your email address will not be published.

Aggregate Crushing Value Apparatus

The oven dried and accurately weighed aggregates are subjected to crushing test on compression testing machine and weight of the resultant fines passing the specified IS sieve to the total weight of the sample expressed a s a percentage is defined as Aggregate Crushing Value. The apparatus is available in three size 75mm dia for 1/8to size ...

Aggregate Crushing Value Apparatus

On Special Request Aggregate Crushing Value Apparatus having 75mm dia or 300mm dia cylinder size can be supplied. Aggregate Impact Tester Make: LabTek Model: SL-AG-002 Origin: India Standards: IS 2386 (PART IV) 9377 & BS 812:112 Specification: It is robustly designed to determine the aggregate impact value (AIV) of aggregates

Crushing Value Apparatus (ACV)

The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure. Three versions available: 300, 150 and 75 mm dia. conforming to NZS 4407:2015.

Correlating Aggregate Friction Test Results Under …

3.2.3 Aggregate Crushing Value Test. The Aggregate Crushing Value Test (British standard 812–110) is used to assess the aggregate crushing resistance by …

Concrete & Highway Engineering Lab Manual

The apparatus for the standard aggregate crushing test (Figure 2.1) consists of the following: (i) Steel cylinder with open ends, and internal diameter 25.2cm, square base plate plunger having ... aggregate crushing value indicates strong aggregates, as the crushed fraction is low. Thus the test can

TRANSPORTATION ENGINEERING LAB MANUAL 2013 DETERMINATION OF AGGREGATE

APPARATUS The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) – 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod of circular cross-section 16mm diameter and 45 to 60 cm long, rounded at one ...

Aggregate Crushing Value Test – Procedure, Result

AIM: Determination of Aggregate Crushing Value Crushing Strength of Coarse Aggregate. Aggregate Crushing value test IS Code is 2386-4 (1963): Methods of Test for Aggregates for Concrete Aggregate Crushing Value Apparatus 1. A 15 cm dia. 2. Steel cylinder with the plunger and base plate. … See more

Aggregate Impact value Test Apparatus, …

Procedure of Aggregate Impact value test. The test sample: normally aggregates sized 10.0 mm to 12.5 mm. the aggregates should be dried by heating at 100-110 0C for a period of 4 hours and cooled. Sieve …

Aggregate Crushing Value Apparatus | Zeal International

Specification: The Aggregate Crushing Value (ACV) test set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat ...

Aggregates crushing value test

After each layer, tamp 25 times for good compaction. Then take the weight of the cylinder with aggregate. Place the apparatus, with the test sample and plunger in position on the compression testing machine. Apply the compressive load of 40 tons in 10 mins. Then remove the specimen from machine and sieve the aggregates through 2.36 mm.

Determination the Crushing Value of Aggregate test

The Crushing Value test measures the ability of an aggregate to resist crushing under a compressive load. It is a measure of the strength and toughness of the aggregate. In this test, a standard crushing load is applied to a prepared aggregate sample, and the percentage of fines generated after the specified amount of crushing is determined.

AGGREGATE CRUSHING VALUE TEST 1. Objective

The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of aggregate ... The apparatus, with the test sample and plunger in position, shall then be placed between the platens of the testing machine and loaded at as uniform a rate as

Aggregate Crushing Value Apparatus

Aggregate Crushing Value Apparatus Description:SE-Test India is the perceptible name in the lab test equipment or instruments market as manufacturers and suppliers. SE-Test India's Aggregate Crushing Value Apparatus (model no. SET-1407) conforms to the IS 2376 (PART-IV) and BS 812:111 industry standards. ...

Aggregate Crushing Value (ACV) Set (Dia 75 mm)

AG1120 set; consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus was produced from galvanized steel. AG1120 Aggregate Crushing Value (ACV) Set (Dia 75 mm) provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load.

Aggregate Crushing Value

Home Civil Engineering Tests. Email This Post. This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) – 1963. The apparatus …

Aggregate Crushing Value Test-Objective, Apparatus, and …

The apparatus for Aggregate Crushing Value Test comprises the following: Fig 1: Aggregate Crushing Value Apparatus. A steel cylinder with a 15 cm diameter, equipped with a plunger and base plate. A straight metal tamping rod with a diameter of 16 mm and a length of 45 to 60 cm, rounded at one end.

AGGREGATE CRUSHING VALUE AND TEN PERCENT FINES VALUE …

AG 0111 Aggregate Crushing Value Apparatus 150 mm dia. AG 0112 Aggregate Crushing Value Apparatus,75 mm dia. Accessories. AG 0111-1 Metal Measure 115 mm diameter x 180 mm deep. AG 0111-2 Metal Measure 57 mm diameter x 90 mm deep. AG 0111-3 Tamping Rod 8 mm diameter x 300 mm long. Request a Quote.

Crushing Value Apparatus

Crushing Value Apparatus. Standard: BS 812:110. This crushing index test apparatus is used to test the fine aggregate crushing resistance so as to evaluate the aggregate road construction applicability. Crushing index apparatus specifications. Mold size: I.D 77mm, depth 70mm. Pressure head dia. 75mm.

Aggregate Crushing Value Apparatus

Find here Aggregate Crushing Value Apparatus, Crushing Value Apparatus manufacturers, suppliers & exporters in India. Get contact details & address of companies manufacturing and supplying Aggregate …

A082 AGGREGATE CRUSHING VALUE …

The complete assembly is cadmium plated for corrosion protection. Weight: 20 kg approx. A083. AGGREGATE CRUSHING VALUE APPARATUS. DIAMETER 75 MM. STANDARD: comparable to BS 812:110. …